OMRON - 3G3MX2-V1

Specifications

Open type (IP20)

Phase-to-phase sinusoidal modulation PWM

0.10 to 400 Hz (or 580 Hz in the high-frequency mode; restrictions apply)

Digital command: ±0.01% of the max. frequency, Analog command: ±0.2% of 
the max. frequency (25±10 °C)

Digital setting: 0.01 Hz, Analog setting: One-thousandth of the maximum 
frequency

V/f characteristics (constant/reduced torque) 
Sensorless vector control, V/f control with speed feedback

Heavy load rating (CT): 150%/60 s 
Light load rating (VT): 120%/60 s

200% of the value of heavy load rating (CT)

0.01 to 3600 s (linear/curve selection), acceleration/deceleration 2 setting 
vailable

2 to 15 kHz (with derating)

200%/0.5 Hz (sensorless vector control)

Starts at a frequency lower than that in deceleration via the STOP command, 
at a value set lower than that during operation, or via an external input. (Level 
and time settable).

Overcurrent, overvoltage, undervoltage, electronic thermal, temperature 
error, ground fault overcurrent at power-on status, rush current prevention 
circuit, overload limit, incoming overvoltage, external trip, memory error, CPU 
error, USP error, communication error, overvoltage suppression during 
deceleration, protection upon momentary power outage, emergency cutoff, etc.

Digital Operator 
External analog input signal: 0 to 10 VDC/4 to 20 mA, Modbus communication 
(Modbus-RTU)

Digital Operator 
External digital input signal (3-wire input supported), Modbus communication 
(Modbus-RTU)

7 points (Selectable from 59 functions)

2 points (Voltage FV terminal: 10 bits/0 to 10 V, Current FI terminal: 10 bits/4 
to 20 mA)

1 point (RP terminal: 32 kHz max., 5 to 24 VDC)

2 points (P1/EDM, P2; selectable from 43 functions)

1 point (1c contact: MC, MA, MB; selectable from 43 functions)

1 point (AM terminal: Voltage 10 bits/0 to 10 V) (Frequency, current selectable)

1 point (MP terminal: 32 kHz max., 0 to 10 V)

RJ45 connector (for Digital Operator)

Control circuit terminal block, Modbus communication (Modbus-RTU)

USB1.1, mini-B connector

Calculate, Logic, Control I/O and so on

AVR function, V/f characteristics switching, upper/lower limit, 16-step 
speeds, starting frequency adjustment, jogging operation, carrier frequency 
adjustment, PID control, frequency jump, analog gain/bias adjustment, S shape 
acceleration/deceleration, electronic thermal characteristics, level 
adjustment, restart function, torque boost function, fault monitor, soft lock 
function, frequency conversion display, USP function, motor 2 control function, 
UP/DWN, overcurrent control function, etc.

-10 to 50 °C (However, derating is required).

-20 °C to 65 °C

20% to 90% RH (with no condensation)

5.9 m/s2 (0.6G), 10 to 55 Hz

At a maximum altitude of 1,000 m; indoors (without corrosive gases or dust)

3G3AX-MX2-ECT

3G3AX-MX2-CRT-E

3G3AX-MX2-DRT-E

DC reactor, AC reactor, radio noise filter, input noise filter, output noise filter,  regenerative braking unit, Braking Resistor, etc.

EN61800-3: 2004

EN61800-5-1: 2007

IEC 60204-1 Stop Category 0, EN IEC 61800-5-2 (STO), EN ISO 13849-1: 2008 
(PLd)

UL508C